Guide Installing Power Shower

Step-by-Step Guide to Installing Power Shower

An energizing shower in the morning might help you get ready for the day. A hotshower in the evening can relieve your day’s anxieties and leave you calm and comfortable for the evening ahead. Showering will reduce your water consumption and electricity bills, essentially carbon footprint, because it uses less water than a bath.When it comes to fitting and installing a new electric shower, you may bewondering, “Can I install an electric shower all by myself?”

Step 1: Carefully remove the old shower unit 

Like all other electrical operations in the bathroom, first, turn off the power tothe bathroom. However, before removing the shower unit, you must first checkthe electrical supply to verify it’s working right before proceeding with anyaction. (A novice electrician can do this, but if you’re uncertain, callan electrician.) When you’re certain that your shower has been switched offat the power source, turn off the water supply as well. Wait until the residual current has dissipated.

Then it’s time to start removing the old shower unit. The great majority of electricshower units are bolted into the wall (four screws are commonly used);therefore, removing them should be simple with a screwdriver. Then lift out theunit from the wall, and that’s it.

Step 2: handling the water supply connection

Examine your new shower unit and its water supply connection, which should be at the exact location of your previous unit. Some types provide various references for easyreplacement. If the specifications aren’t the same, you may need to perform some modifications. Next, loosen four screws, two at the top and two at the bottom, to remove the frontpanel of the new shower unit. Now you can see the electrical andwater connections, which should move up and down on a hinge.

If your new shower unit does not fit in the same space as your old shower, and it willbe evident at this point. The difficulty for this step depends on case-specific details, and in some cases, requires complex plumbing and electrical skills.

Step 3: Make adjustments for Installing a Power shower

Mark the location of the new unit on the bathroom wall and try to cover up any holes left by the previous device – a pencil is an excellent alternative to avoid leaving permanent marks on the wall surface. In addition, mark the locations of any new screw holes that must be drilled.

Then, using a drill, successfully boreholes into the wall. This can be a difficult task, so take care not to damage any neighbouring tiles. When drilling into the wall, use a masonry bit rather than a hammer, as this will result in damaged tiles. After drilling holes in your bathroom wall, install roll plugs and then screw in your new shower.

Step 4: Examine the electrical shower.

After connecting the new electric shower to the wall, double-check that everything inside the unit is in the proper position. This comprises all wires, including neutral, live, and earth, as well as any pipes. To make sure you’ve followed all the instructions correctly, seek the assistance of a professional before resuming the use of the water and electricity.

Once you are confident that the wiring is in the correct location, screw the front of your electric shower unit back into place and reconnect the power and water supplies. When testing your new shower, use utmost caution to ensure that everything is in working condition. Electrical showers can cause terrible and life-threatening accidents, combining water and electricity in a humid environment, especially when installing a power shower.

What are the safety requirements when installing an electric shower?

It’s a little more challenging to set up the electrical supply than to set up the plumbing. The size of the cable and fuses for electric showers varies according to the shower’s output (in kW). We recommend going with a 10sq mm cable because it will allow you to upgrade your shower without installing a larger wire in the future. A separate fused electrical supply circuit will be required for the electrics. To turn the power supply to the shower on and off safely, you’ll need a switch safely mounted in the ceiling, with neon indicators for steamy showers).

It’s easier to install some electrical shower models, so choose wisely.

Showers with top, bottom, side, and rear cable and pipe entry points are the easiest to install because they make cable and pipe routing easier. Showers with greater space inside the casing and well-designed connecting blocks will make things easier for the installation, as wires are sometimes big and rigid. Look for swivelling water connections with enough place for a spanner as well. To finish the job, make sure the riser rail and shower handset are high enough for anyone in the usual height spectrum to use the shower, yet low enough for youngsters.

Final advice: electrical showers can be a deadly combo if you install them poorly.

You need to have experience in installing power shower units from the ground up, and you’ll need a Part P-certified plumber or electrician to install, upgrade, or check the wiring to verify that the shower is safe to use. Everyone thinks they can install it themselves, but you might be able to pull it off if the model you’re installing is similar to the old one and doesn’t need complicated modifications. In this example, the power and water cables are already in place, so all that’s left is installing a brand new shower unit.

If the new Power shower unit’s wattage is higher than the previous one, an electrician should replace it because the cabling may need to be changed. Finally, remember that installing an electric shower can be challenging in certain circumstances and bathrooms with unique features, so call an electrician instead of a futile attempt at installing power shower.

Posts created 62

Leave a Reply

Your email address will not be published. Required fields are marked *

Related Posts

Begin typing your search term above and press enter to search. Press ESC to cancel.

Back To Top